S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

坞式舰船压载系统研究

对坞式舰船压载系统设计中需考虑的稳性、作业时间、注排水方式等问题进行了分析研究,可供有关设计人员参考.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Dynamic Simulation of a Smart Crank and Slider Mechanism

In this paper, a smart crank and slider mechanism is analyzed mostly from a dynamic view. By means of dynamic explicit finite element method, 3D nonlinear structure is simulated. It is proved that the mechanism can effectively accomplish smart movement prescribed. And in order to ensure reciprocal movement with higher frequency, measures should be taken to avoid over heating of parts. Compared with internal energy, kinetic energy of total rigid body is dominating, and Y direction equivalent rigid velocity is much higher than X direction velocity. Equivalent rigid velocity of all parts is consistent with respective movement condition. For both energy and velocity, slider effect is dominating. Three direction equivalent inertia force oscillates. Force amplitude in Y -direction is comparitively the greatest.     

Maritime accident investigation and temporal determinants of maritime accidents: A case study

This paper presents the results of an investigation into temporal determinants of maritime accidents based on a data-set obtained from the proceedings of formal inquiries in the former German Democratic Republic (GDR). The results show that there is no statistically significant outcome between the probability for an accident and the time of watch. Thus the results do not confirm previous studies, which reported significant time of day effects.The outcome of this study indicates that marine inquiries can provide useful data for an analysis of underlying causes of maritime accidents. It is suggested that accident inquiries should be extended into the area of watch systems employed and should record the hours of work and of rest of the officers on the watch involved in a maritime accident.     

The role of professional associations in shipping

This article is in three parts. The first covers the historical development of qualifying associations. The second covers the particular role of maritime institutions that include The Royal Institution of Naval Architects, The Institute of Marine Engineering Science and Technology and The Nautical Institute. The third and final section considers the future for maritime professional associations in the context of international shipping.     

对我国航运企业发展物流的探讨

1我国航运企业实施物流战略的条件分析 从海洋运输走向综合物流,是国际航运企业发展的大方向,也是航运企业迎接现实挑战、实现可持续发展的必由之路.我国加入WTO后,航运企业从单一海洋运输向现代综合物流服务的转变显得更加紧迫.经过近20年的发展,我国航运物流取得了一些进展.随着我国改革开放的不断深人,社会的物流意识已经形成,开展航运物流的条件也逐步成熟.概括地讲,主要表现在以下几方面:     

Virtual prototype simulation on underwater hydraulic impingement shovel

The virtual prototype technology is applied to the design of the hydraulic impingement shovel, which is to increase the reliability of the design. The work principle of hydraulic impingement shovel is expatiated, and its dynamic equations are established. The 3D model of virtual prototype is built by PRO/E. Then the couple between the mechanical body of prototype and the hydraulic system is completed by virtue of ADAMS. Finally, the simulation is made on the virtual prototype. The simulation results show that the design of underwater hydraulic impingement shovel is rational. The virtual prototype technology could lay sound foundation of successful manufacturing of physical prototype for the first time and offer highly effective and feasible means for the design and production of underwater equipments.